LP hose with QCC-I type one regulator fits all grills 3/8 flared female fitting for grill manifold and 24 inch hose.

36" LP Hose Regulator. Fitting is 3/8 inch flared female onthe hose and a QCC hand wheel on the regulator made to fit standard LP tank valves.

No Rust stainless steel hose guard slides over gas line to protect hose and regulator from hot BBQ, rodents that may chew the gas line, rough wall openings, etc. Hose Guard is coiled like a spring so it can be adjusted and can be used with several guards together.

Hose Guard details

Keep spiders out of burners and orifices in grill burner. Screens to go onto the end of barbecue grill burners in order to block insects from burners and from getting into orifice and valves.

Burner Spider Screens

Replacement regulator for Natural Gas Grill with 1/2 inch female attachments. Buy this regulator for NG bbq grills and if you are converting a barbeque from LP (liquid propane) to natural gas.
LP regulator allows gas at approx 11 inches of water column and natural gas regulators regulate gas at 2 inches water column.

table top regulator with orifice is made for portable grills. Regulators includes on/off, high/low valve and dispences propane directly into the gas grill burner.
This does snot fit every portable barbeque but may need to be manipulated to fit a lot of models. Check your model and be sure.

Replacement regulator/ and valve for portable infrared gas grill. Regulator control includes threaded orifice that attaches to the grill body. This regulator valve is the US threads for models with the serial number 17-005997 and greater. Earlier model Anywhere infrared grills need the SOL-17-4AZ which replaces the regulator valve, electrode and the stainless mounting box that the module and the regulator installs into.

Regulator Valve Information

Regulator Valve Information

Coversion kit to convert the Solaire infrared gas grill metric regulator to American threaded regulator. This item replaces the box that mounts to the side of the grill so the threading will hold a US thread regulator.

Replacement Regulator Information

Brass fitting for gas hose connection. 3/8 inch flared male to 3/8 inch flared male fitting used to join two gas hoses. The flared fitting is a sealed attachment that does not need plumbers putty or teflon tape. 3/8 inch flared is the most commonly used gas hose.

Brass fitting for gas hose connection. 3/8 inch flared male to 1/4 inch pipe male fitting used to join the hose and regulator to the manifold on Weber models and some others. The flared fitting does not need teflon tape or plumbers putty but the 1/4 inch pipe fitting does need a sealant.

Fitting flared three-eights adapts to fit one-half pipe thread. This fitting is most commonly used to attach a propanle hose and regulator to a barbecue grill manifold. Half-inch pipe on one side and three-eights flared on the other.

Often a portable barbecue grill for tailgating, recreational vehicles and boats has a regulator attachment designed to attach to portable tanks.
This fitting has a 3/8 inch male attachment for a gas line and a male attachment exactly the same size as a portable LP tank. This fitting allows the barbecue to be attached to a larger propane gas tank instead of using the portabke tank.

Orifice from Turbo rotisserie. The rotisserie valve has a gas line attached in the control panel and the orifice screws to a compression or flared fitting at the back of the BBQ where it enters the rotisserie burner venturi. If you are converting the gas type for your Turbo gas grill this is the rotisserie orifice. Look at your orifice to be sure.

See Replacement Grill Orifice

Spud style brass orifice w2ith male thread. This orifice is a longer design than a lot of spud style orifices. The length of the orifice puts the flow of gas in the right place in the venturi so the air shutter pulls air into the burner in LP barbecues.

As with any of these orifices, Let Us Know if you want the orifices drilled for LP or NG. For NG please know the regulated gas pressure you will be using.

Gas barbecue grill conversion orifice. New orifices are blanks and need to be drilled to the proper BTU rating of each burner. Every valve has its own orifice.

This extended orifice fits the same 1/8 pipe thread control valves as the 31700 and 37900 control valves. Orifices are new and are not drilled for LP or NG. Please email or call us for assistance wih orifice settings.

Brass orifice fits the 88935 control valve above for Grand Turbo and Turbo Select gas barbecue grills. Orifices are new and are not drilled-out for natural gas or for liquid propane. If you need the orifice set to a specific BTU or gas tyoe please send an e-mail after the order is placed or call on the teleohone numbers below.

Gas line adapter to attach to one pound lp gas tank. 1 lb LP tanks are often used for camping and portable travel. This adapter will attach to a one pound lp gas tank and is one-quarter inch inner diameter pipe on the opposite side to attach to a regulator or a gas line.

Gas fitting adapter for residential propane cylinders. Adaptor threads into (POL) inside reverse thread of LP tank cylinder to convert the tank to QCC fitting. If you have a tank with only inner threads to connect regulator this adapter will allow you to use newer regulator with large handwheel.
More Information

Gas line adaptor to create union of three gas lines. T fitting most often used to use one gas line and attach a barbecue grill and a side burner. Use this T fitting to allow 2 appliances to pull gas from one tank or one gas line. Three-eights flared male connections.
T Fitting Detail

Barbecue grill adapter for gas line joins half-inch pipe thred to three eighths flared fitting. Adapter has male 3/8 inner diameter male on one side and 1/2 inch pipe female on other side.

Gas line fitting converts to a three-eighths inside diameter flare. Male end (left side in image) is 3/8 inch flare fit. Pipe end (right side in image - double threaded inside and outside) is 3/8 female pipe thread in the inner thread and half-inch pipe thread outer male thread.

Convert regulator to POL to attach regulator to LP tank with inside thread on cylinder valve. New regulators have QCC to attach to the thick outer threads on an LP tank. Replace handwheel with the fitting to attach regulator with LP cylinders inside threading.