Thermal Engineering Corp - TEC - Infrared Gas Grill Replacement Parts

TEC Models:

Servicing infrared gas grills for many years, I have seen one problem with the infrared gas burner over and over again. Moisture. If water gets into an infrared burner while it is not burning and the water gets into the housing it must be drained. Extract it from the grill and leave it upside down for a few hours. If the burner is lit while water is in the housing the ceramic tiles can crack. The water condensates from the intense heat and is forced from the stainless housing so fast a small crack will form n the tiles. While you are cooking, if the tiles shift from internal gas pressure the burner will go out.

Sometimes the flame will just die and sometimes it can make a "whoosh" or "pop" sound but either way it ts telling you to replace your infrared burner.

Infrared burners on right side of these images is the original TEC burner. The infrared burner on the left side is the infrared replacement burner installed.

TEC Sterling Burner at 16 Years:

TEC Infrared Burner
Patio II & Sterling II

Infrared Burner, stainless steel with ceramic plate (requires 2 each for Patio II and Sterling II; 3 each for Sterling III). Includes mesh.
Check TEC Infrared Burner Size and manufacturing information for this model.

TEC Infrared Burner Screen Only

TEC Cooking Grates

V-Channel Grilling Grate, 14.75" w x 12.75" deep, stainless steel (requires 2 each for Patio II and Sterling II; 3 each for Sterling III).

TEC Sterling II Pilot Assembly

TEC ignition pilot kit assembly for TEC Sterling II is the replacement grill parts used as the ignition on the original infrared gas grills.

Ceramic Tile For TEC Infrared Burner

TEC Infrared Burner

Infrared replacement burner for TEC grill repair. TEC grill repair for Patio 2 and Sterling 2 and Sterling 3 infrared gas grill burner by Rasmussen. High quality materials and modern manufacturing.

TEC Cooking Grate

TEC replacement cooking grate for TEC Patio 2, Sterling 2 and Sterling 3 is 14.75 x 12.75 inches. V grate design continues the TEC concave grid design to add flavor while grilling but using the V grid is much easier to clean and maintain the grilling grate.

TEC Cooking Grate

TEC replacement cooking grate for TEC Patio 2, Sterling 2 and Sterling 3 is 14.75 x 12.75 inches. This is the original U grid manufactured by TEC for these model. The Patio 2 and the Sterling 2 uses 2 grids and the Streling 3 uses 3 of these. This is the grid that has the U channel design and small holes in the front for drippings.

TEC Pilot Kit

The older TEC infrared gas BBQ grillsused a pilot to ignite the infrared burners. The igniter module wires to the electrode to ignite the pilot which lights the infrared burner. This TEC replacement pilot ignition kit attaches to the manifold to replace the original pilot.

TEC Double Igniter Pilot

TEC double pilot replacement kit for TEC infrared gas grill repair.

82357

TEC infrared gas grill electrode

Infrared gas grill electrode for older infrared gas grills and newer infrared gas grills. The two posts allow the igniter to arc between the two points and ignite gas emitting from the infrared gas grill burner.

82358

TEC new gas grill electrode

New TEC gas grills use a rectangular stainless steel burner with has angled shields that magnify heat for infrared temperatures without the original pressurized ceramic tile burners. This electrode spark arcs against the stainless steel material of the burner.

82359

TEC infrared gas grill control valve

This is a replacement control valve for TEC Patio II, Sterling II and Sterling III control valves. Some of the TEC infrared gas grill models had clamps instead of this bolt design so check your valve before ordering.

TEC Control Valve.

TEC - Thermal Engineering Corporation - BBQ grill repair control valve. The control valve screws right into the manifold. Use a sealant when attaching the control valve to the manifold. The hood style orifice attaches to thecontrol valve; use your existing orifice for either natural gas or liquid propane.

Replacement rotary spark generator ignition module for TEC barbecue grill repair. Two screws hold the rotary module on the control panel. Electrode wire connects to the rotary module ignition from nside the control panel.

TEC Patio I infrared burner replacement

The original TEC Patio I infrared burner with two venturi tubes. TEC stopped making this replacement burner for the original infrared Patio gas grills. They are available for a limited time until stock is depleted.

TEC Sterling I infrared replacement burner

The original TEC Sterling I infrared burner with two venturi tubes that attach to TEC grill valves at the front of the infrared grill. TEC stopped making this replacement burner for the original infrared gas grills. They are available for a limited time until stock is depleted.

Black plastic replacement control knob for TEC infrared gas grills

Liquid propane regulator and twenty-four inch gas hose with 3/8 inch female flared attachment.

Tec BBQ Grill Cover. Heavy vinyl padded weather cover for built in Sterling II infrared gas grill models by TEC, Thermal Engineering Corporation.

Tec BBQ Grill Cover. Heavy vinyl padded weather cover for infrared Patio II gas grill models by TEC. Thermal Engineering Corporation full-length cover for Patio II on a cart with One side shelf.

TEC Heavy duty Patio 2 model gas grill cover. Full length cover for a Patio 2 infrared gas grill with Two side shelves.

The original Patio Two drip pan by TEC was not fabricated of stainless steel. This new replacement TEC drip pan is manufactured by Thermal Engineering Corp using American made 304 stainless steel.