Repair Parts for Turbo Gas BBQ Grills from BBQ Galore

Battery holder and button igniter replacement for Turbo gas barbecue grill repair. The battery holder button mounts in the control panel of many older style Turbo gas BBQ grills. Because the manifold is too close to the control panel the module with the button and battery is too big to fit inside the control panel. This battery holder button is wired to a seperate module - 88593 below -- and that module is wired to the electrodes that spark at the burners inside the barbeque grill.

Electrode and collector box cross over ignitor for Turbo gas BBQ grills allows spark ignition and crossover ignition from one grill burner to the next burner.

Click here for additional information about this electrode.

2 Spark Module works with item 2100226 listed above. The module installs into the control panel and the electrodes plug into this module. This is the 2 spark module so there are two spade outlets for either 2 electrodes or 1 electrode and 1 ground wire.

4 Spark Module installs into control panel with 4 spade outlets for up to 4 connections. Works with item 2100226 above and plugs into grill electrode ignition.

Some Turbo electronic ignition systems have a bettary pack with a button that attaches to a module that attaches to the electrodes that spark at the burner. This module is from the older style igniter with three parts. This module has 4 prongs to attach 4 electrodes for use with turbo grills with up to 5 burners.
Although image is green, modules are often black.

Replacement rotary ignitor with single outlet to fit Ducane, Profire, DCS, Lynx and many hundreds of other gas grill models. Module installs with 2 small screws in control panel and has a single outlet for electrode to plug into.

Mechanical piezo rotary ignitor with two outlets to connect to two electrode wires or one electrode and a ground. Ducane, Profire, DCS and many other grill models use this piezo rotary spark generator.

Replacement ceramic electrode ignitor used to repair BBQ grill models by Amana, Surefire, Tuscany and other barbecue grills. With a simple mounting bracket and long steel post an electriode like this can be used to repair most barbecues.

Igniter Electrode 106730

Barbecue grill repair ignition electrode. Check the mounting for your gas barbecue. This electrode is easy to moint inside the barbeque because the clip allows the electrode to install through the front firewall of the BBQ or install through a hole in the mounting brackets with a single screw.

universal control knob. Universal knob. Selectable D position (refers to the shape of the control valve post), socket diameter (6mm or 8mm), and shaft length (flush, 0.25”, or 1.625”. Shafts can also be trimmed to desired length). Includes six inserts (shafts) and set screw. Fits any grill with inside bezel dia. greater than 2.1875”.

Replacement regulator for Natural Gas Grill with 1/2 inch female attachments. Buy this regulator for NG bbq grills and if you are converting a barbeque from LP (liquid propane) to natural gas.
NG regulator ships with water filter for outdoor use. An LP regulator allows gas at approx 11 inches of water column and natural gas regulators regulate gas at 2 - 6 inches water column. This NG regulator has half-inch pipe thread female connections. COntact us directly if you need something else.

Gas BBQ grill valve for some Turbo gas barbecues. This valve does not have the ignition attached and it clamps to the gas manifold. Also used for Charbroil other imported gas grills. This valve is used on the Grand Turbo and the Turbo Select. The valve stem is different from the original so knobs will need to be manipulated to fit or replaced to fit the valve. Item 02342 - shown above -works perfectly.

Replacement gas valve for turbo STS gas grills.

720-0057-3B - 720-0057-4B - 750-0057-4BRB and STS Turbo grills CG3TCN, CG4TDN, XG3TCN, XG4TDN.

This valve has the electrode attached to ignite the gas grill burner. This gas barbeque valve has a long extension where the orifice attaches to the valve. Please let us know if your gas grill uses liquid propane or natural gas when ordering. Actual Valve is Not a Flame Thrower Style Control.

Flat ceramic radiant use in several Turbo gas barbecue grills including Turbo Select models and Grand Turbo models. This item contains a package of four (4) ceramic tile radiants. Radiant tiles are 7 1/16 inches by 4 3.4 inches.

Orifice from Turbo rotisserie. The rotisserie valve has a gas line attached in the control panel and the orifice screws to a compression or flared fitting at the back of the BBQ where it enters the rotisserie burner venturi. If you are converting the gas type for your Turbo gas grill this is the rotisserie orifice. Look at your orifice to be sure.

See Replacement Grill Orifice

Spud style orifice. From one flat to another flat this gas orifice is 7/16 of an inch wide at the hex-head. The orifice comes with a starter hole and can be used for propane and for natural gas. If you need assistance understanding the conversion from one gas type to another let us know and we can help.

Spud style orifice can be used in a liquid propane or natural gas barbecue grill. Orifice is 3/8 of an inch wide from flat to flat at the head. Starter hole can be opened a little for LP gas or a little bit more for NG. As with any orifice let us know if you need assistance or an explanation of what a certified technician will do when converting your BBQ.

This extended orifice fits the same 1/8 pipe thread control valves as the 31700 and 37900 control valves. Orifices are new and are not drilled for LP or NG. Please email or call us for assistance wih orifice settings.

Brass orifice fits the 88935 control valve above for Grand Turbo and Turbo Select gas barbecue grills. Orifices are new and are not drilled-out for natural gas or for liquid propane. If you need the orifice set to a specific BTU or gas tyoe please send an e-mail after the order is placed or call on the teleohone numbers below.

Brass fitting for gas hose connection. 3/8 inch flared male to 3/8 inch flared male fitting used to join two gas hoses. The flared fitting is a sealed attachment that does not need plumbers putty or teflon tape. 3/8 inch flared is the most commonly used gas hose.

Brass fitting for gas hose connection. 3/8 inch flared male to 1/4 inch pipe male fitting used to join the hose and regulator to the manifold on Weber models and some others. The flared fitting does not need teflon tape or plumbers putty but the 1/4 inch pipe fitting does need a sealant.

LP propane manifold for STS barbecue grill for the turbo model gas grill that has an infrared sear zone and rotisserie burner kit. The control valves, orifices, wires and ignition switches are all included and installed on this manifold.