Capital Gas Barbecue Grill Replacement Parts

Capital BBQ Grill W burner. This heavy stainless steel replacement burner fits the Capital Performance and Precision barbecue grill models. Overall dimensions for total length and total depth of the burner are 8 7/8 x 19 7/8 inches.

Capital BBQ Grill replacement W burner for Capital Performance and Precision barbecue grill repairs. Overall dimensions for the burner are 9.5 Inches wide x 19 7/8 inches long. These can be easily differentiated because this W burner has thick cross-over tubes towards the top front of the burner.

82300-01

Capital BBQ Grill W burner. This heavy stainless steel replacement burner fits the Capital PSQ barbecue grill models.
Burner overall size is 17 x 7 inches.

Infrared replacement burner for Capital barbecue grills. Infrared searing burner is 19 1/4 inches long at the bottom (without the back bracket) and is 20 3/8 inches long with the back bracket and the burner is 9 3/8 inches wide. The infrared burner comes with the back bracket and ignition electrode.

Replacement infrared grill burner for Capital models. Note this burner is visually different from the infrared burner above because of the back ledge and electrode that is not in this burner.

This infrared burner fits the same models as 82321-2 burner above and 10758-01 radiant below.

Replacement vaporizer radiant for Capital barbecue grill models with the W burner82321 listed above. Radiant tray dimensions are 17 7/8 x 10 7/8 inches.

Radiant heat shield fits Capital PSQ models exactly. This includes the notch around the flash tube ignitor. Stainless heat shield installs above W burner to spread heat, conduct heat and deflect drippings. Alternative to the original, not from Capital and installs above 82321 burner.

Capital CG model grill radiant trays. These are probably the heaviest radiant heat shields of any barbecue grill On The Planet!! Porcelain rods are locked-in to 18 Gauge 304 stainless steel and welded in place permanently. Each stainless section is 11.25 inches by 6.25 inches.

Replacement vaporizer radiant for Capital barbecue grill models using the 82300 burner above. Heat shield dimensions are 16 1/16 x 11 1/8 inches.

Replacement vaporizer radiant for Capital barbecue grill models using the 82300 burner above. Heat shield dimensions are 16 inches deep x 15.5 inches wide.

Capital gas grill ignition electrode replacement for main barbecue burners. Capital Cooking Systems PSQ Grill.

Installation is counter-intuitive. Electrode will be bent and possibly clipped to install into flash tube. Look at the original and contact us for assistance with this installation.

Capital gas grill ignition electrode replacement for all main barbecue burners. 24 Inches from flat mounting bracket to tip of electrode wire. Ceramic is 2 inches long.

Ignition electrode and ignitor wire for Capital infrared BBQ grill burner.

This U shaped electrode installs on back wall so Capital infrared burner ignition electrode steel tab touches the U to conduct electricity instead of attaching a wire like every other ignitor electrode in the world.

Replacement igniter electrode for Capital rotisserie infrared burner.

Rotisserie electrode installs in the stainless box on right side of infrared rotisserie burner next to the thermocouple tip.

Replacement electrode for side burner. The electrode for the side burner has a metal cap to spark at 360 dgeree circumference of the tip for reliable gas ignition in the side burner range.

Glow Plug 12 Volt ignitor electrode for Capital gas grills. The tip of this ignition electrode will glow like a light bulb to ignite gas from within the collector box. See picture bottom left side of this page.

24 Volt Glow Plug ignitor electrode for Capital gas grills. The tip of this ignition electrode will glow like a light bulb to ignite gas from within the collector box. See picture bottom left side of this page.

Replacement electrode and collector box for Capital Professional model barbecues. The collector box is about 2.75 inches long and has 2 mounting holes. The electrode wire is about 22 inches long.

Flash tube replacement facilitates ignition with or without electronic sparking ignition. Flash Tubes install simply with only 2 screws.

Sparking electrode installs inside tube but when ignition does not work, flash tubes allow ignition with a match or lighter.

Replacement Ignition spark generating module used in barbecue grill models manufactured by Capital Cooking Systems. The nine-volt module has 2 Flat Male Spade connectors to connect Two ignition electrodes. This module also has Two larger spade plugs which connect to the momentary switch so the module is Live as long as this button is pressed. Capital wire kit is not used with this igniter.

Nine Volt Ignition Module used in outdoor gas grill models. Module mounts to outside barbecue and holds a nine volt battery. Some kind of momentary Button or interuption switch connects to this igniter module as a trigger and up to Four electrodes connect for rapid sparking ignitor.
Discontinued By Manufacturer, But Still Available.

Push button replacement for 9 volt ignition systems in multiple Capital models. Capaital grills have two different nine-volt battery powered modules and this same button is used to start ignition in both grills.

Replacement switch for Capital barbecue grills. Button Lights Up when pressed to turn on. Switch works like a toggle to control BBQ lights.

Light switch toggle design for Capital gas grill lights.

Capital Cooking Systems has been unable to deliver these switches but another switch has been made available.

Ignitor module replacement for Capital Professional models. The nine volt battery wires connect to the module and then connect to the momentary button mounted in the control panel. Module has 4 outlet connections to connect up to 4 electrodes in the grill.

Ignition connection attaches nine volt battery to the ignition module and the momentary button.

Replacement electric all-in-one spark generater module. This type of module is the spark generator, the button, the battery holder and mounting bracket all in one product. The nut under the button holds the spark generator to the front control panel so only the button sticks through the barbecue grills panel. The button unscrews to be able to remove and replace the AAA battery without removing the entire module.

1.5 Volt AAA battery ignition module. Battery installs under the button and a nut holds the module to the control panel. Ignitor has 4 connectors for using up to 4 igniter electrodes together. Less than 4 can also be used by grounding unused ignition connections.

Replacement control valve for Capital Professional and Performance models. The control valve screws into the gas manifold at the bottom and the gas orifice which determines BTUs for NG or LP threads to the tip of the valve.

Capital control valve replacement with ignition micro-switch. This clamp-on control valve fits newer model Capital models. The micro switch connects to the power source and the igniter electrode so the ignition is automatic when the control knob is pressed in.

Capital replacement safety valve for rear infrared rotisserie burner.
The safety valve allows gas flow using heat through the thermocouple so gas will stop flowing if the flame goes out.

Both Capital control valves use this gas orifice. This same orifice is used for Natural Gas and for Propane grills.

Order the hose and regulator with orifices to allow us to drill the orifice before shipping. All orifices must be drill based on the regulator pressure to the manifold for a specific BTU Certification so we will also need you to tell us Your Capital Grill Model in the order notes or separately in an email once the transaction is completed.

Rotisserie Elbow Connection attaches aluminum gas hose from Capital rotisserie safety valve to the rotisserie. The elbow then bolts through the rotisserie burner and the orifice attaches to the adaptor.

Chrome heavy metal knob replacement for Capital barbecues. We find this control knob generally on Titanium and Professional named models by Capital Grills.

Replacement Capital Grill control knob with black grips and red writing. Valve stem insert in back of knob can be installed in any direction for easy use.

Control knob replacement with velvet-like red grip, red printed text and mirror polish. Valve stem connection under the control knob is detachable. The red control knob was primarily used on the Capital side burner models.

Cast stainless steel concave cooking grate for Capital barbecue grill models. Replacement cooking grate is 19.5 inches long and 6 1/8 inches wide. Always purchase with quantity of a set. Concave design holds flavor when searing and manages grease for barbecuing.

Capital Stainless Steel Cooking Grate Replacement is 17.25 Inches Deep and 12 3/8 Inches Wide. Cut-out opposite corners make the grate simple to raise and lower in place. Depending on the model of Capital Professional or Titanium multiple grates will be used including the half-size grid below.

This Capital Stainless Steel Cooking Grate is 17.25 Inches Deep and 5.75 Inches Wide. These grates are installed with the wider grids above in some Titanium and Professional models.

Warming Rack Grate replacement. Primary rectangular section is 24 by 6 inches which does not account for mounting clips on back corners.

Capital BBQ Grill Titanium and CCE model 26 and 32 use this warming rack.

Replacement Manifold for the 32 Inch Capital Professional Model barbecue grill. The manifold is a total width of 19 inches left to right with 3 hole for the control valves. Front to back is 16 inches and ends with a male 1/2 inch pipe thread for the gas line attachment.
Currently Unavailable.

Replacement Manifold for the 26 Inch Capital Professional Model barbecue grill. The manifold has one-eigth pipe thread holes for the control valves and welded mounting brackets for installation.
Currently Unavailable.

LP hose with QCC-I type one regulator fits all grills 3/8 flared female fitting for grill manifold and 24 inch hose.

Long 40 Inch LP Hose and Regulator. Rubber Hose Fitting is Three-Eighths inch flared female and a QCC hand wheel on the regulator made to fit standard LP tank valves with the fat external threading.

LP regulator with two hoses for side burner and bbq grill connection. This comes with two hoses coming out of one regulator and as one hose that splits into two hoses. Same result but two different styles. Use one regulator and one tank to operate both appliances.

Two Stage Propane Regulator with 24 Inch gas hose. Gas hose connection is 3/8 flared female. Use this regulator with large Capital BBQ grill models capable of burning more than 65K BTU's.

A common LP cylinder needs this regulator for higher BTU barbecues because of the rate liquid propane vaporizes.

Replacement regulator for Natural Gas Grill with 1/2 inch female attachments. Buy this regulator for NG bbq grills and if you are converting a barbeque from LP (liquid propane) to natural gas.
LP regulator allows gas at approx 11 inches of water column and natural gas regulators regulate gas at 2 inches water column.

In-Line Liquid Propane Appliance Regulator.

When using a large permanent propane tank the gas line will connect to the barbecue with this low-pressure appliance regulator.