DCS Gas Barbecue Grill Repair Parts.

Ceramic radiants dcs for even heat distribution and radiant heat at the grilling surface to achieve searing temperatures. The 8.5 inch radiant rods were used on some of the very early DCS models that moved away from lava rocks. The DCS-36D and the DCS-48-D models that ended with BQR and BQAR started with these 8.5 inch radiant rods. Later versions of the same models used the 9.5 inch radiant rods.

Ceramic radiant replacement 3 pack for DCS gas grills manufactured through the past ten years. DCS radiant rods conduct and augment heat for even distribution and searing grilling surface temperatures.

9123Pack10

Pack of 10 ceramic radiants dcs conduct for even distribution and grilling surface temperatures. Porcelain rods are still functional of they are dirty. Rods only need to be replaced when broken. The goal is to absorb and radiate heat -- not look pretty. In lesser barbecues broquettes and lava rocks are used but the evenly spaced porcelain rods in a DCS collaborate to maximize heat distribution at the grilling surface.

Hard white DCS briquettes come in a pack of twenty-four pieces.

Replacement DCS Warming Rack Grate for BGA 27 gas barbecue grill models. This is the original warming grid design that slides into channels on the right and left side of the grill.

Igniter Electrodes, Collector Boxes, Brackets and Ignition Wires

Replacement DCS ignitor electrode with collector box and wire. This sparking ignitionassembly has been used in Dynamic Cooking Systems barbecue grills for more than 2 decades.

DCS Ignitor Electrode To Fit Smaller Left or Right Collector box. Old barbecue grill models with right side and left side collector box igniter electrodes use this electrode. Bracket has flat mounting panel with hole on one side and pin for mounting to collector box bracket on the other side of the electrode.

Right Side Mounting Collector Box Bracket with Electrode.

Left Side Mounting Collector Box Bracket with Electrode.

ceramic electrode with wire for older model DCS barbecues with right-side and left-side electrode igniters and collector box brackets.

Includes electrode, bracket, collector box and electrode wire.
Some models may need to bend a mounting tab but this electrode is very simple to install.

47 inch wire with female spade and square plastic connectors, used with dcs battery powered spark generators.

Electrode wire for round connection. 20 inches long with One Female spade connector and One Round Female Connector for a simple fit to any of the male spades on these gas bbq grill ignition electrodes that needs to attach to a rotary module.

20" wire with female spade connectors. Made to connect igniter electrodes and modules for Chargrillers, Great Outdoors, Jenn Air, Vermont Castings and others.

DCS electrode with spring and mounting clip for side burner igniter electrode replacement.

Electrode replacement kit for older DCS side burner. The single electrode lights both burners on the DCS double sideburner.

igniter details

These are going extinct and will soon be gone.

Electrode and stainless steel collector box for DCS 24 inch gas barbeque grill.
This is both items and because the DCS 24 has not been made in many years they are very expensive.

Electrode only. Electrode in threaded sleeve for easy installation. The tip comes extra long to be clipped on site for setting the gap. It is possible to leave the tip long and move the spark which can make the ignitor more effective.

Rotisserie igniter electrode with electrode wire long enough for the 36 and 48 inch DCS models.

Replacement sparking electrode installs to the DCS smoker burner and installs on the DCS infrared rotisserie burner. Compare the metal installaton bracket to the bracket on your rotisserie. The metal sparking rod is fabricated to be too long so we can bend or clip as needed. DCS electrode details click here

Replacement 24 vac glow plug ignition electrode used in DCS E Model gas grills. These DCS BBQ grills plugged into an electrical outlet. Ignition glow plug electrodes are capable of igniting the burners glowing like a lightbulb. DCS barbecue grills were the first to use hot surface ignition electrodees which are so prevalent today in high-end grills. Two wires pre-attached to hot surface glowing relectrode, 12 inches long.

Electrode with wide bracket and flat installation bracket for easy mounting onto the DCS smoker burner. The electrode can be used to ignite the rotisserie butn this electrode fits best the DCS smoker brner just below the wood chip smoker.

The DCS E model was decades ahead of its time!! Twenty Years Ago DCS had Hot Surface glow plug ignition electrodes which most high-end BBQ grill companies are only just learning how to install today. This replacement transformer is the 24v transformer replacement inside the electrocal box on the DCS E model.

Spark Generator Ignitor Modules

Dcs ignition module with 8 eight outlets for eight electrodes to plug into. This is good for the 48 inch models with side burners, rotisserie, smoker and grill burners that use 8 electrode igniters. Button installed into control panel wires to this models. Nine volt battery (not included).

Replacement 9-volt battery powered spark generator ignitor module used in DCS barbecue grill models with a D in the model. For Instance: DCS36D is a D model. These originally had manual rotary ignitors (listed below) but changed to the 9 volt modules almost immediately.

Nine volt module has 6 outlets to control up to 6 electrodes. Two larger spades connect momentary button(s).

Replacement rotary ignitor with single outlet to fit Older DCS BBQ grills and other gas grill models. Module installs with 2 small screws in control panel and has a single outlet for electrode to plug into.

Piezo rotary ignitor with three outlets can be plugged in to 3 electrode wires to send sparks to three different electrodes from one turn of the knob. This module has been used on most brands of barbecue at some time.

This replacement igniter module is considered an all-in-one module because the button, module, battery and spade outlets for the electrodes are all one item. This is the module used on the DCS 132 and 131 side burner range models but can also be used on some of the older DCS25, DCS26 and DCS 27. modles'

Replacement electric all in-one spark generater module. This type of module is the spark generator, the button, the battery holder and mounting bracket all in one product. The nut under the button holds the spark generator to the front control panel so only the button sticks through the barbecue grills panel. The button unscrews to be able to remove and replace the AAA battery without removing the entire module.

Push button replacement button for DCS barbecues with a 9 volt battery ignition system. The hole in the control panel is designed to allow the button to push into the opening. Removing this switch requires removing the control panel and squeezing the sides to push back out of the control panel.

DCS E models were not manufactured or sold for very long. A lot of these barbecues were sold in outdoor kitches islands and through catalog magazines.
This is the button that activateS the glow plug hot-surface electrodes which glow like a small lightbulb to ignite the grill burners.

Control Knobs

Stainless Control Knob fits DCS gas BBQ Grills, old and new. This Solid Heavy Knob comes standard on newer DCS grills. New DCS grills use the same control valve as the original DCS grills thirty years ago so this new heavy stainless knob can be installed on Any DCS barbecue. Check overall diameter; approx 2 1/4 inches. Newer DCS BGC models use a cheap knob colored to look higyh-quality but this is the only solid metal knob ever made by and for DCS barbecue grills.

universal control knob designed to look like the DCS satin finish knob shown above. Selectable D position, socket diameter (6mm or 8mm), and shaft length (flush, 0.25 or 1.625”. Shafts can also be trimmed to desired length). Includes six inserts (shafts) and set screw. Fits any grill with inside bezel dia. greater than 2.1875”.

Knob Details

New DCS Owners discontinued this knob. Call For Stock Before Buying or Use K1002342 below. Black plastic DCS control knob. This fits older models of DCS BBQ grills. Check overall diameter approx 2 1/2 inches.

Black plastic DCS control knob 211043 slightly smaller than 2 inch diameter. This control knob is a Set Of Two Knobs fits some of the older models of DCS BBQ grills. Check overall diameter 2 inches or be sure to check model of DCS gas barbecue grill.

Replacement Bezel for Many DCS gas barbecue grill models. This is the bezel that is just larger than two inches inside diameter. We use this bezel with the smaller black knobs 211043 above and the satin finish knobs on the BGA and BGB models which mount right on top of them.

Rotisserie Replacement and Repair Parts.

two deluxe 4-prong heavy duty meat forks for half inch diameter spit. These forks clamp to rotisserie spit rod to hold food barbecuing evenly. Thicker forks are for larger foods like roast, turkey, tenderloin, prime rib, etc.

T Handle designed to press against mounting posts on the bottom of the rotisserie motor. The rotisserie motor has two mounting posts that install into two holes on the side of the DCS grill to support the rotisserie motor when installed on the grill in use. These T handles thread into the mounting block and press against the motor posts to hold the motor solidly mounted to the grill.

Spit rod replacement handle for heavy duty DCS rotisserie spit rod.

Rotisserie Motor For DCS BGB model barbecue grills. This rotisserie motor installs on the Right Side of the grill with two posts that slide into a locking base. Above the spit rod mount is a halogen light that has its own switch so the light can be used independent of the rotisserie motor.

DCS Rotisserie Motor. DCS grills have had several different rotisserie motor designs. This is one used in the middle of DCS manufacturing when the popular "D" models were selling. Like the newer BGB model rotisserie motors this motor installs with two posts on the bottom that slide into a bracket on the grill.

Stainless steel single roller to repair rotisserie bracket. Rollers attach to the rotisserie bracket so the rotisserie spit rod rolls smoothly.

Roller bracket replacement support for rotisserie spit rod. Bracket installs right side of DCS rotisserie and rollers attach for clean spit rod movement. Rollers are not included with bracket.

Support bracket installs on the Left side of the fire box to support revolving spit rod. Rollers are shown above and are not included. This is the almost-flat support bracket and rollers bolt through this support.

DCS replacement rotisserie receiver bracket.

This stainless steel replacement bracket accepts the rollers -- sold separately above -- and bolts to the side wall of the DCS grill as heavy rolling support for the spit rod.

Rotisserie gas line connection for gas orifice. This DCS elbow adaptor connects the rotisserie gas line with a compression fitting. The elbow bolts to the rotisserie venturi and the orifice attaches to the tip. The same size orifice fots this rotisserie elbow as the control valve orifices.

Replacement orifice and gas line mounting bracket for DCS infrared rotisserie burner. Gas line comes from front safety control valve around the barbecue to attach to the rotisserie burner venturi tube with an elbow bracket and threaded spud orifice.

Orifice for DCS infrared vertical rotisserie burner. The Rotisserie control valve does not have an orifice because the orifice attaches to the installation elbox at the venturi of the burner.

Protection for the 16 inch Infrared Rotisserie Burner. This is the porcelain coated protective cover that mounts on top of the infrared rotisserie burner in the DCS "A" models and some others. The protection panel is curved to wrap around the top of the grill ledge above the rotisserie burner.

Rotisserie thermocouple and ignition electrode cover. Rotisserie collector boxes mount on either the right side or the left side of the infrared rotisserie burner in order to support the thermocouple and electrode while hiding the wires and gas lines that attach to the controls and the burner.

Left Side

Right Side

Thermocouple replacement for DCS models. This thermocouple is long enough for all DCS model rotisserie safety valves.

Replacement safety valve for DCS gas bbq grill rotisserie. Gas line goes into safety valve and out of safety valve to rotisserie burner. Thermocouple attaches to allow or to stop gas flow using millivolts generated by heat as a safety feature that stops gas leaks.

Partially refunded when selected with button and bezel below.

Safety button fits on button for DCS rotisserie safety valve. This is the button that fits in to the 11050 bezel for the rotisserie valve and attached a top the valve button.

When safety valve, button cover and bezel are shipping together, a partial refund will be appliedapproximately 2-3 days after delivery.

Replacement bezel threads to rotisserie safety valve from outside the control panel. Actual replacement is New DCS Stainless design.

When safety valve, button cover and bezel are selected together, a partial refund will be applied approximately 2 days after delivery.

The New DCS Stainless Steel Bezel is all available.

Gas Jet Orifices And Fuel Regulators.

DCS replacement hood style orifice with #72 starter hole and 1/8 female pipe thread.
Generally, the only reason to change an orifice is because the gas type is changing. We'll drill these Blank orifices if the regulator is included in the transaction with the orifices. The LP or NG regulator pressure setting determines the drilled-opening size so we can only drill the orifices to the certified BTU rating if the orifices and regulator are together.

Spud style replacement gas orifice for BGB132, BGB131 and "E" model single and double DCS side burners. This hex-head is 7mm.

Side burner main jet holder. Gas line attaches to aluminum coupling and burner attaches at top with DCS orifice in the center.

DCS control valve. This valve fits all of the DCS grills. The rotisserie uses a safety valve with a thermocouple so this valve will not work for a rotisserie but the grill valves are al the same BTU and the same size at the manifold so this valve should work with all models of DCS. Our service technicians use this valve for everything DCS and we have not needed any other valve for the barbeque grills

LP hose with QCC-I type one regulator fits all grills 3/8 flared female fitting for grill manifold and 24 inch hose.

36" LP Hose Regulator. Fitting is 3/8 inch flared female onthe hose and a QCC hand wheel on the regulator made to fit standard LP tank valves.

LP regulator with two hoses for side burner and bbq grill connection. This comes with two hoses coming out of one regulator and as one hose that splits into two hoses. Same result but two different styles. Use one regulator and one tank to operate both appliances.

Two Stage Propane Regulator with 24 Inch gas hose. Gas hose connection is 3/8 flared female. Two foot long rubber gas hose. Two stage regulators are used in gas barbecues with higher BTU flow than most -- as much as double the gas flow. These are usually found on larger sized infrared grills and should be used on any low pressure LP appliance pulling more than 65,000 BTU from a residential portable LP tank.

Three Foot extension hose with 3/8 inch flared female ends extends regulator and hose. Use to extend regulator hose, often used with built in BBQ grill accessories like LP tank pull-out drawer.

Hose and Regulator with POL attachment. This male threaded regulator is callede a POL attachment and was the standard for LP consumer fittings before the safety features needed a new way to denote added safety mechanisms in the LP cylinder. 24 Inches long with a female 3/8 flared attachment on the hose. This can fit old LP tanks And new LP cylinders.

Replacement regulator for Natural Gas Grill with 1/2 inch female pipe thread attachments. Use with NG bbq grills and if converting a barbeque from LP (liquid propane) to natural gas.

In-Line Liquid Propane Appliance Regulator.

When using a large permanent propane tank the gas line will connect to the barbecue with this low-pressure appliance regulator.

Ten Foot Quick Connect Gas Hose. Pneumatic gas line is 3/8 flared female and 3/8 flared pipe thread but ships with thread adaptors for 1/2 pipe to fit the DCS manifold and regulator when ordered together.

Gas manifold for BGA 26 DCS models. The Manifold is a black pipe that connects to the gas line to deliver gas to the control valves. There is no difference between NG or LP in the manifold.

Gas manifold for BGA 27 DCS models. The Manifold is a black pipe that connects to the gas line to deliver gas to the control valves. There is no difference between NG or LP in the manifold. Check your model or call for assistance as there are several models of 27 inch DCS gas grill.

Smoker Drawers And Installation Parts.

DCS smoker burner support.

Replacement stainless steel smoker tray for DCS 36 and 48 inch barbecue grill models with smoker trays. This tray is the newer design with the handle that is bent around from the top of the face plate. The older design had a removable handle.

Replacement stainless steel smoker tray design from the older DCS barbeque grill models. This smoker tray design had the ability to remove the handle and the faceplate. This sale is for the tray itself - use the old hanlde and face plate or call us to order the entire assembly.

DCS smoker drawer details

Handle for stainless steel wood chip smoker from DCS.

Heat plate with cross over tube installs below DCS BBQ burner so the cross over tube is in between the burners. This is a safety device created for better and faster ignition or DCS gas grills.

The stainless steel tube allows the gas flame to pass from one burner to another so burners will light off the flames of other barbecue burners even if the ignition electrode is not working. The tube that slides under the level of the burners deflects grease to the drip tray below the barbeque grill.

DCS Wheel, Casters, Hood Handle, Covers and All Else.

Replacement chrome end cap bolts to DCS barbecue hood to hold the hood handle in place. The hood needs two of these end caps to hold the stainless pipe hood handle.

Contact us if this is needed. These were recently listed No Longer Available and may not be for long.

Spacer looks like black plastic but is a phrenolic heat-resistant material installed between the stainless DCS hood and the end-cap handle-holder.

Ceramic hood handle spacer used in DCS barbecues a log time ago.

Like the black synthetic spacers used today, original DCS grills used these ceramic spacers to protect hood handle supports from heat.

Overall Dimension is 2 x 1.25 Inches.

Hub Cap for DCS wheel. Hub cap is just slightly wider than five inches diameter.

Solid Eight Inch Wheel. The DCS 8 inch wheel does not take air but is a Heavy, solid rubber wheel. Actual diameter is 8 inches with a half inch center axle hole.

Wow! Please Know -- We Do Not Make The Price!!

Replacement DCS Axl Spacer installs between solid 6 inch wheel and cart axle. The stainless spacer is one inch long and 5/8 inch outside diameter.

DCS Replacement caster wheel with brake toggle switch on side to lock wheel.

Not usually a stock item. We order these as we need them.

DCS Replacement Caster Wheel without locking brake.

Not usually a stock item. We order these as we need them.

When a built in DCS grill is installed in an outdoor kitchen with a side burner use this T fitting so a single gas line or a single tank will send gas the the DCS barbecie and the side burner together. 3/8 inch inner doameter for propane to split one gas line to 2 appliances.
T Fitting Detail

This grill has been discontinued for over five years but there are a lot of them in use. The cover is still available...sometimes. Working with Fisher and Paykel is difficult.

Full length cover for a DCS 27 inch gas barbecue grill. The DCS 27 inch models usually had a few different configurations. Unless you let us know otherwise this cover will ship with a full lenght cover designed for use with the 27 inch grill on a DCS cart with a single shelf mounted on one side as in the image posted here. If your DCS grill has a different configuration, please email us and let us know after placing the order so we ship the correct grill cover.