Original and New Grill Parts for Ducane Barbeque Grills.

push-button piezo plunger with external grounding prong and mounting nut. Grounding prong may also be used to conduct charge to a secondary electrode in grills with a side burner.

This may be the most used igniter module in the world of grilling! Hundreds of thousands of Weber models have this ignition and dozens of other models all used this same piezo with the mounting nut to hold the igniter to the control panel.

push-button piezo plunger with three electrode plugs. This igniter module was very popular in the original Ducane barbecues where two electrodes were controlled with this one piezo button and the third outlet was used as a ground.

OEM style control knob. D = 12. Ducane bbq grill replacement control knob for most older, original Ducane - made gas barbeque grills. D-12 means the D shaped hole has the flat side in the twelve-o'clock position when Off.

Replacement rotary ignition module with single outlet to fit Ducane. Mechanical ignitor modules tend to last A Very Long Time.

Wire connections are round male connections.

Replacement rotary ignition module with two outlets. Turning the rotary module knob will send sparks to two electrodes and light both burners in Ducane barbecue grills.

Replacement rotary ignitor module has three outlets so turning the knob sends sparks to three electrodes simultaneously.

Mechanical igniter modules usually last much longer than electronic ignitors. Wire connections are round male connections.

Replacement battery powered ignitor. This spark generator can fit any barbeque grill controlling up to Four ignition electrodes sparking at 4 burners.

Under button is one AA battery. As long as there is a hole to install the button through, the module is simple ignitor for all BBQ's.

Replacement module for any gas barbecue grill ignition system. All-In-One battery powered ignitor has 2 outlets to connect two electrodes for any barbecue ignition system.

Wire connections are flat eighth inch male spades and top button covers the battery.

Replacement ignitor spark generator with 6 electrode connection brackets.This ignition module can be made to work with any barbeque that has a hole in the control panel or by placing a hole in the control panel. AA battery is under the button which unscrews to replace the battery.

Replacement ignitor attaches to round burners in original Ducane model barbecues. Assembled repair ignition electrode includes the collector box, mounting bracket, sparking electrode, wire, and female connector to fit Ducane models.

Replacement ceramic electrode can be wired to any module with flat spade connector. Perpendicular flat mounting bracket has nut/bolt making electrode easy for installation anywhere on the barbecue.

Ignition electrode design has longer ceramic on the back side to hold wiring away from possibility of heat.

Replacement ceramic electrode inside threaded sleeve with multiple thin nuts threaded to sleeve.

Sparking electrode has long steel tip which can be bent and clipped as needed. Tightening thin nuts on both sides of bracket holds sparking ignition electrode in place.

Older model, original replacement Ducane control valve .

This control valve fits original Ducane models fabricated by the Ducane family when they still owned the brand.

Replacement control valve for newer Ducane barebcue grill models. The control valve has a rotary module inside and an attached electrode wire and electrode in a bracket. The control valve is also the copmplete ignition system for the Ducane barbeque.

Limited Stock...Soon to be extinct!

This control valve has the same clamp-on attachment and angle to the orifice as originals no longer made. The stem is slightly narrower than the original but longer to the knob.

Use as orifice with Above Valve Replacement.

Although DUC3042 has inner threads that match the original Ducane orifice, using this 88318 on the outer threads will add about 1.25 inches to the tip of the valve.

Replace or Install new stainless steel rotisserie burner housing to fit Ducane rotisserie burner. These flanges push the heat from the Ducane burner towards the spit rod when using the rotisserie.

This insert drops into the back of the grill firebox to support the back of the cooking grates and holds the rotisserie burner.

Replace or install new stainless steel rotisserie burner housing to hold rotisserie burner and direct heat to where food would be turned on the spit.

This insert holds the rotisserie burner in the grill and connected to the front valve while radiating heat and supporting cooking grates.

Red pyramid style briquettes are -- unfortunately -- No Longer Available.

Replacement orifice can convert valve to use natural gas or to propane fuel. Hex head is 1/4 inch. Orifice threads to tip of control valves with automatic ignition. Newer Ducane BBQ's will have flame-thrower valves with integrates ignition.

Orifices come as blanks or will be drilled to appropriate BTU rating when ordered with the regulator and hose to be installed with orifices.

Replacement gas Orifice for many Ducane models. Replacement gas orifice in tip of valve is 9/32 inch hex-head diameter.

Orifices can be ordered alone as blanks and ordered drilled to factory Certified BTU levels if ordered with the regulator and hose being installed with orifices.

Orifice used in many rotisserie connections. Look at your orifice to be sure. Rotisserie orifice is installed in the actual burner in the back wall. We used these like a template to match replacement length and threading so the actual replacement may look different.

As with other orifices, select regulator with orifices.

Hood orifice for older Ducane valves. Use the replacement orifice when converting fuel to natural gas or propane.

Orifices come as blanks or will be drilled to appropriate factory settings when full configuration is ordeered with the LP or NG regulator being installed with orifices.

LP hose with QCC-I type one regulator fits all grills 3/8 flared female fitting for grill manifold and 24 inch hose.

Replacement regulator for Natural Gas Grill with 1/2 inch female attachments. Buy this regulator for NG bbq grills and if you are converting a barbeque from LP (liquid propane) to natural gas.
LP regulator allows gas at approx 11 inches of water column and natural gas regulators regulate gas at 2 inches water column.

Ten foot long gas hose with pneumatic connector designed for outdoor strength. Quick-connect end makes the hose easy to attach and remove in case the appliance has to be moved. Gas hose is shipped with adaptors and threaded unions for easy installation from shut-off valve the regulator and grill.

Replacement regulator for LP, propane gas, has half-inch female pipe thread attachments.

This is the residential appliance regulator installed between the shut-off valve and gas BBQ. We use an adjustable regulator set for approx 11 inches of water column displacement.

Brass fitting for gas hose connection. 3/8 inch flared male to 1/4 inch pipe male fitting used to join the hose and regulator to the manifold.

Female-to-female 3/8 flared connectors. This can be useful for attaching from the Weber manifold when we need to attach a natural gas regulator.

Fitting flared three-eights adapts to fit one-half pipe thread. This fitting is most commonly used to attach a propanle hose and regulator to a barbecue grill manifold. Half-inch pipe on one side and three-eights flared on the other.

T Fitting allows one LP tank to feed gas to side burner and barbecue grill together. The T fitting turns a single gas hose into two gas lines for 2 appliances together.
T Fitting Detail