Dynasty Gas BBQ Grill Repair Parts

Heavy cast iron replacement burner for Dynasty barbecue grills. Cast iron venturi and gas sealing gasket and hardware is included. Dynasty H shaped burner design is 17.5 inches long and it 8 inches wide.

Stainless vaporizer briquette support tray for Dyansty barbecue models. Replacement heat shield is 18 inches by 11.25 inches and designed to fit Dynasty and some models used to vaporize drippoings and conduct rising heat using red pyramid briquettes.

Briquette shield replacement for Dynasty barbecue grills. This briquette shield has a cut-out for Dyansty and Jenn Air gas grills with a smoker drawer. With the cut away the smoker tray fits in the BBQ where the cut-out section of briquettes is installed.

Replacement control valve for Dynasty model barbecues originally manufactured by Jade and branded as Jenn Air or Dynasty. Dynasty control valves attach directly to the gas manifold pipe and then have a gas hose inside the control panel to connect to the orifice elbow union which connects to the H burner in these BBQ grill models.

Replacement electrode and heavy gauge stainless collector box which opens to the right side. Electrode is long enough to be easily cleaned or bent to create better gap for hot sparking. Collector box is much heavier than any other ignition collector brackets.

Stainless Steel collector box and Ignition electrode assembly. This ignitor does not have a wire attached and comes mounted with a bolt inside a long protective collector box with Two mounting holes and hardware.

Replacement ignitor electrde with extra long tip to be bent as needed. Threaded sleeve with installation nuts will facilitate attaching this ignitor to the rotisserie box on the Dynasty back wall. Total length is only about 28 inches so existing wire will need to be spliced or added.

Electrode wire for piezo spark generator modules. 20 inches long with One Female spade connector and One Round Female Connector for a simple fit to any of the male spades on these gas bbq grill ignition electrodes that needs to attach to a rotary or piezo button module.

20" wire with female spade connectors. Made to connect igniter electrodes and spark generator modules in all types of barbecue grills and any igniton system connection.

47” ignition electrode wire with female spade and square plastic connectors used with battery powered spark generators to connect igniter electrodes and modules for All barbecue grill ignition connections.

Usually a rotisserie connection because of the length. However, if More length is needed and you select wires to be connected together, just let us know and we'll send connectors with the wires.

Ground wire with a female spade and a round connector for use with spark generator connection to ignition electrode.

Add or replace ignitor module ground in ignition systems. Any ignition module spark generator with an extra outlet connection Must Be Grounded.

Control Knob is not like the original Dynasty or Jenn Air barbecue controls but fits and stainless veneer looks extraordinary on the barbecue. Diameter is 1 7/8 inches.

Replacement rotary ignitor with single outlet to fit older Dynasty barbecue grill models and many other gas grill models. Module installs with 2 small screws in control panel and has a single outlet for electrode to plug into.

Mechanical piezo rotary ignitor with two outlets to connect to two electrode wires or one electrode and a ground. Ducane, Profire, DCS and many other grill models use this piezo rotary spark generator.

Piezo rotary ignitor with three outlets can be plugged in to 3 electrode wires to send sparks to three different electrodes from one turn of the knob. This module has been used on most brands of barbecue at some time.

Universal hose and regulator for all models of gas barbeque grill. Single 24 inch hose 3/8 with 3/8 flared female end. This gas hose and regulator is made to fit 90 percent of liquid propane

White hard briquettes come in a pack of Twenty-Eight pieces. Older Style briquettes break-up and fall apart because of greases, marinades, sauces being absorbed while cooling and heating. These porcelain hard white briquettes are not porous and will last exponentially longer than older briquette types.

Red pyramid style briquettes are not manufactured by any grill manufacturers any longer because they were constantly being replaced as moisture soaked into the briquettes and caused the material to crumble.

Replacement regulator for Natural Gas Grill with 1/2 inch female attachments. Buy this regulator for NG bbq grills and if you are converting a barbeque from LP (liquid propane) to natural gas.
LP regulator allows gas at approx 11 inches of water column and natural gas regulators regulate gas at 2 inches water column.

No Rust stainless steel hose guard slides over gas line to protect hose and regulator from hot BBQ, rodents that may chew the gas line, rough wall openings, etc. Hose Guard is coiled like a spring so it can be adjusted and can be used with several guards together.

Hose Guard details

Universal 4 Spark gas bbq grill ignition module. AAA battery screws under button and nut hold module to control panel with 4 attachments for using up to 4 ignitor electrodes together. Less than 4 can also be used by grounding unused electrode attachments.

Replacement electric all-in-one spark generater module. This type of module is the spark generator, the button, the battery holder and mounting bracket all in one product. The nut under the button holds the spark generator to the front control panel so only the button sticks through the barbecue grills panel. The button unscrews to be able to remove and replace the AAA battery without removing the entire module.