Lynx Gas Barbecue Grill Igniter and BBQ Grill Replacement Parts.

New Glow Plug Electrodes For Lynx models after 2010. Hot-Surface ignitors are also glow plug electrodes that use a higher voltage transformer and are very heavy-duty compared to the discontinued glow plugs Lynx used previously.

This is a set of 3 electrodes as shown. The shrter glowing electrode is the the grills' rotisserie.

Lynx Hot Surface Retro-Fit Kit for 54Inch models. Heavy hot-surface glow plugs, new higher powered transformer with all the instructions, wiring and stainless brackets for installation replacing post-2006 glow plug models.

Lynx replacement electrode for Lynx barbecue grill repair models made in 2006. Includes wiring. In 2007 Lynx started using the glow-plugs. This 2 prong electrode arcs to itself and is too small to get often covered in grease. This is a very reliable gas barbeque grill igniter design.

Lynx electrode and collector box -- Left Side Of Burner. Heavy stainless steel collector box protects the ignitor sparking against inner stainless. Gas is caught in the box to ignite. These Lynx electrodes are very long and were installed into older Lynx BBQ grill models for many years. The wire is included. Igniter and collector box install On The Left Side of The Burner In the Lynx barbeque grill.

Lynx electrode and collector box (listed below) look identical to the more commonly used electrode and collector box listed above. This version of the electrode is much smaller than the longer more commonly used electrodes. From the installation bracket to the tip of the electrode is 2 inches. From the bracket back to the end of the wire is 16 inches.

Smaller collector box for 31217 ignition electrode. Collector box is 2 1/8 inches long and 1 1/8 inches total width. Overhang igniter bracket forces gas to move and collect in the pocket where the electrode sparks against the clean underside of the collector box bracket.

Lynx replacement ignitor electrode for the infrared rotisserie burner. From mounting bracket to end of electrode wire is 46 inches.

New model of Lynx switch button lights up blue when active.

Gas barbecue module for Lynx gas grill models. Module mounts to hold a nine volt battery. Button/switch connects to this module and Lynx igniter electrodes connect to this module.

Safety Valve button for Lynx rotisserie. The rotisserie valve allows gas-in and gas-out but blocks the gas inside the valve. The thermnocouple heats-up to pulls the inner solenoid open and allow gas flow. Gas flows through the safety valve only so long as the thermocouple is hot.

Control valve replacement for infrared rotisserie burner. This valve installs to the manifold on the bottom and then mounts the safety valve button on top so gad can flow to the Lynx rotisserie burner.

Thermocouple replacement for Lynx models with this safety valve button. This thermocouple is long enough for all models at 72 inches to install from the tip of the valve to the rotisserie burner connection at the orifice.

Rotary module for Lynx gas barbecues. Older Lynx gas grill models used to have rotary modules that installed in the control panel. Electrodes plugged into the back side of the rotary module so the electrode could arc and ignite when the rotary was turned.

Mechanical piezo rotary ignitor with two outlets to connect to two electrode wires or one electrode and a ground. Ducane, Profire, DCS and many other grill models use this piezo rotary spark generator.

Piezo rotary ignitor with three outlets can be plugged in to 3 electrode wires to send sparks to three different electrodes from one turn of the knob. This module has been used on most brands of barbecue at some time.

Lynx hood thermometer installs into the double-wall stainless steel barbecue hood on Lynx gas gril models. Hood thermometer comes with locking nut, trident bracket, washers and 3.25 inch thermometer. All the necessary pieces are included and instructions with color pictures are in the package.

Lynx gas barbecue grill clips hold briquettes onto heat shield briquette tray. This order is for a Quantity of 10 clips. Ten stainless clips that attach in between the briquettes on the briquette tray.

Replacement mesh screen for Lynx ProSear burner. Screen is approximately 7.25 inches by 13.75 inches.
Mesh screens are always on infrared burners to protect the burner from falling food and heavier items.

Replacement mesh screen for Lynx ProSear burner. Screen is approximately 7.25 inches by 15.5 inches.
Mesh screens are always on infrared prosear burners to protect the burner from falling food and heavier items like briquette trays or cooking grates that could damage ceramic burner.

Fits 31183 and 31885 prosear burners.

Replacement mesh screen for Lynx ProSear burner. Screen is approximately 10 1/8 inches by 15 1/8 inches.
Infrared burner screens are easily installed by pressing the edges of the screen over the edge of the infrared burner.

L.E.D. Lights connections for Lynx 30 models. Wire harness has one male and one female connection to attach l.e.d. lights for control knobs across Lynx control panels.

L.E.D. Lights connections for Lynx 54 models. Wire harness has one male and one female connection to attach LED lights for control knobs across Lynx control panels.

Lynx barbecue grill interior light housing with bolb, light cover and wiring.

Power transformer and power cord with plastic attachments for Lynx gas grills since 2007. Lynx grills since 2010 use this transformer which is more powerful than previous versions because the new hot surface ignition electrodes burn hotter than the previous glow plug igniters.

Power cord attachments for Lynx gas grills manufactured since 2007. The transformer plugs into the grill but in order to transfer the electrical power to the rotisserie and throughout the grill these wires plug in to the new fittings on Lynx barbecues.

Electrical connection to Lynx rotisserie motor.

Lynx replacement briquettes from Lynx BBQ grills. White briquettes from Lynx packaged as quality of 35. These cases of 36 briquettes are the original factory briquette originals that come directly from Lynx.

New ceramic briquette made specifically for Lynx gas bbq grill models. Gas barbecue grilling briquettes are natural in color and come as 48 pieces in a package.

Lynx elbow connects gas line from safety valve to rotisserie burner. Gas through manifold feeds to control valve which connects to the safety valve button and then gas connects to the rotisserie where this elbox mounts to the infrared rotisserie burner.

Rotisserie Orifice. When converting a Lynx to Natural Gas or to Liquid Propane the orifices have to be changed for every burner. This is the brass orifice for the infrared rotisserie burner.

Let us know the model converting so we send the orifice properly drilled.

LP or NG orifice fits Infrared ProSear and Smoker valve in 30, 42, 56 and main burner valves in 27, 36 Lynx models. Check Your Orifices To Be Sure of the size.

Let us know the model converting so we send the orifice properly drilled.

Lynx Main Burner Orifice. Convert Lynx 30, 42, 56 BBQ Grill to NG or LP.

Let us know the model converting so we send the orifice properly drilled.

Lynx 27 Warming rack for the 27 inch models fabricated before 2006.

The twenty-seven inch Lynx warming grate is 26 7/8 inches wide at the furthest point, including the mounting posts and 24.5 inches wide without the mounting post. The front to back depth is 9 1/8 inches.

Replacement Warming rack for Lynx 27 inch Professional gas grill models manufactured after 2005.

The warming rack grate is slightly deeper than 9 inches and has a noticable design difference -- please note the visual difference.2 This warming rack grid was installed in Lynx barbece grill models from 2006 forward.

Replacement Warming rack for Lynx 36 inch Professional gas grill models.

The warming shelf grate is 9 inches deep and 33 3/8 inches wide but total width with the installation rod sticking out right and left is 35 7/8 inches.

This is the warming rack grate installed in 36 Inch Lynx models before 2006.

Replacement Lynx 36 warming rack for inch Professional gas grill models manufactured since 2005.

The warming rack grate is 9 inches deep and 34.5 inches wide.

Lynx stainless steel cooking grates. Grill Grids for 27 Inch Lynx grill are 18.5 inches deep and 12 inches wide. Grates are sold individually but used in grill as multiple grates.

Heavy-duty outdoor grill cover for Lynx 36 inch barbecue grills on portable cart. Lynx name logo is on the outside as shown. Heavy vinyl, form-fitted stiching and inner padding make the outdoor weather cover extraordinarily durable. A split up the front with a flap-covered zipper makes the cart easy to put on and remove from the grill.

LP hose with QCC-I type one regulator fits all grills 3/8 flared female fitting for grill manifold and 24 inch hose.

36" LP Hose Regulator. Fitting is 3/8 inch flared female onthe hose and a QCC hand wheel on the regulator made to fit standard LP tank valves.

LP regulator with two hoses for side burner and bbq grill connection. This comes with two hoses coming out of one regulator and as one hose that splits into two hoses. Same result but two different styles. Use one regulator and one tank to operate both appliances.

Two Stage Propane Regulator with 24 Inch gas hose. Gas hose connection is 3/8 flared female. Two foot long rubber gas hose. Two stage regulators are used in gas barbecues with higher BTU flow than most -- as much as double the gas flow. These are usually found on larger sized infrared grills and should be used on any low pressure LP appliance pulling more than 65,000 BTU from a residential portable LP tank.

Replacement regulator for Natural Gas Grill with 1/2 inch female attachments. Buy this regulator for NG bbq grills and if you are converting a barbeque from LP (liquid propane) to natural gas.
LP regulator allows gas at approx 11 inches of water column and natural gas regulators regulate gas at 2 inches water column.

In-Line Liquid Propane Appliance Regulator.

When using a large permanent propane tank the gas line will connect to the barbecue with this low-pressure appliance regulator.