Sunbeam Grill Parts

Original Sunbeam design control knob. Replaces Sunbeam part number 40-2466. Valve stem insert D shape opening equals 9.

Barbecue Warming rack for Sunbeam models approximately 26.5 inches by 8.5 inches deep. This kind of warming rack is made to slide forward and back as the hood opens and closes.

This kind of electrode is normally mounted into a collector box in the center of an H shaped or Oval shaped burner like the old Sunbeam models used. There is a tension clip in the collector box and a spring on the electrode that provides low-mass grounding points for the spark and the ability to move within the collector box.

Twenty inch electrode wire with 2 female ends. One end is flat and the other end is round. Either end can be easily shped to be round or flat but having them flat and round allows the wire to easily clip to newer battery modules or older piezo modules.

Insulated electrode with tiny tip for use inside thin collector box. The small tip allows the electrode to be placed inside the stainless bracket and still spark against the top, bottom or sides depending on what is cleaner and closer for a strong arc.

Collector box bracket for many Sunbeam barbecue models using H shaped burners and Oval burners with single or double venturi tube connections to the control valves. The bracket holds to the burner and the electrode clips into the stainless to arc inside the protected material inside where the gas if forced to accumulate.

Collector box bracket for many Sunbeam barbecue models using H shaped burners and Oval burners with single or double venturi tube connections to the control valves. The bracket holds to the burner and the electrode clips into the stainless to arc inside the protected material inside where the gas if forced to accumulate.

LP hose with QCC-I type one regulator fits all Sunbeam LP grills 3/8 flared female fitting for grill manifold and 24 inch hose.

36" LP Hose Regulator. Fitting is 3/8 inch flared female onthe hose and a QCC hand wheel on the regulator made to fit standard LP tank valves.

LP regulator with two hoses for side burner and bbq grill connection. This comes with two hoses coming out of one regulator and as one hose that splits into two hoses. Same result but two different styles. Use one regulator and one tank to operate both appliances.

No Rust stainless steel hose guard slides over gas line to protect hose and regulator from hot BBQ, rodents that may chew the gas line, rough wall openings, etc. Hose Guard is coiled like a spring so it can be adjusted and can be used with several guards together.

Hose Guard details

Keep spiders out of burners and orifices in grill burner. Screens to go onto the end of barbecue grill burners in order to block insects from burners and from getting into orifice and valves.

Burner Spider Screens

Replacement regulator for Natural Gas Grill with 1/2 inch female attachments. Buy this regulator for NG bbq grills and if you are converting a barbeque from LP (liquid propane) to natural gas.
LP regulator allows gas at approx 11 inches of water column and natural gas regulators regulate gas at 2 inches water column.

table top regulator with orifice is made for portable grills. Regulators includes on/off, high/low valve and dispences propane directly into the gas grill burner.
This does snot fit every portable barbeque but may need to be manipulated to fit a lot of models. Check your model and be sure.

Brass fitting for gas hose connection. 3/8 inch flared male to 3/8 inch flared male fitting used to join two gas hoses. The flared fitting is a sealed attachment that does not need plumbers putty or teflon tape. 3/8 inch flared is the most commonly used gas hose.

Brass fitting for gas hose connection. 3/8 inch flared male to 1/4 inch pipe male fitting used to join the hose and regulator to the manifold on Weber models and some others. The flared fitting does not need teflon tape or plumbers putty but the 1/4 inch pipe fitting does need a sealant.

Fitting flared three-eights adapts to fit one-half pipe thread. This fitting is most commonly used to attach a propanle hose and regulator to a barbecue grill manifold. Half-inch pipe on one side and three-eights flared on the other.

Often a portable barbecue grill for tailgating, recreational vehicles and boats has a regulator attachment designed to attach to portable tanks.
This fitting has a 3/8 inch male attachment for a gas line and a male attachment exactly the same size as a portable LP tank. This fitting allows the barbecue to be attached to a larger propane gas tank instead of using the portabke tank.