Viking Ignition - Double-Prong Electrode.

The double Prong ignitor electrode is the best igniter design in my opinion. The evolution of barbeque grill igniters has grown to glowing hot-surface ignitors which glow bright like a very intense light bulb but earlier designs that required a collector box bracket and newer designs that glow are not more effective then the double-tip ignitor electrode. They are a whole lot easier to beak though. Older and newer ignition electrodes are generally a lot more expensive and difficult to repair whereas the double-prong electrode requires one, single screw and will spark regardless of Any Module used. These double prong tip electrodes can be attached to older rotary modules or Any battery controlled modules and even the electrical plug models and this electrode functions Perfectly with Any Ignition Module type in any position of Any Viking model. .

Viking BBQ Grill Parts Viking Ignition Flash Tube Viking Ignitor Button
Item Description Price Illustration

4488090

Original Viking gas barbeque grill Heavy Gauge ignitor electrode replacement used to repair Viking BBQ model igniters.

In the ignition assembly, the electrode is the spark plug and this electrode Sparks to ignite the U burner in dozens of different Viking models.

See images below and bottom left corner and See if igniter is Original fabricated for Viking. Original from Viking For Viking Gas BBQ Grill Models will be Longer on back side of mounting bracket so the wiring attaches well clear of heat and flash-flames.

$36.


Free Shipping Cont'l USA!!
gas bbq grill replacement electrode starter for viking gas bbq grills

.63 inch from the mounting bracket to the end of the porcelain housing.

4488091

Slightly Longer Replacement Electrode for Viking gas barbecue grill models which also contain single straight pipe burners with the U burners. This electrose is slightly longer than the other Heavy Gauge Double Prong ignitor electrode because the straight pipe burner will have ignition ports located different.

Item 4488091 replaces Viking grill PB040288 which is another discontinued igniter.

Original Viking replacement ignitor electrodes are Very Long on back side of mounting bracket to keep clear wiring from heat and flame. This replacement welectrode is made to light the straight pipe burner which Viking calls the smoker burner but the wonderful thing about these long double prong electrodes as igniters is they are easy to bend and clip as needed if installing at infrared tru-sear, rotisserie, U burner or elsewhere.

$37.


Free Shipping Cont'l USA!!
gas bbq grill replacement electrode starter for viking gas bbq grills

1.35 inch from mounting bracket to end of porcelain housing.

brass t fitting flare thread to gas hose

All Viking Models All Positions.

Viking gas barbecue grills have evolved throught the years to become a much better appliance than where they began. This particular feature is one that has been installed in Viking gas grills for over ten years. The adjustable warming rack grate is not a new feature to Viking gas grill models. The warming racks are capable of moving up and down on a support bracket that has three tiers. The warming rack can be set level at three different heights to allow better clearance while barbecuing or to adjust the affect of the heat of the grill.

viking trusear all infrared burner with ignitor electrode viking trusear infrared burner and igniter electrode

As shown in this image the double prong ignition electrode on the infrared Tru-Sear burner is mounted to the back of the burner in the Viking grill models that are All Infrared. This TruSear burner is only installed in all infrared models.

Viking gas grills with only one Tru Sear infrared grilling burner have the ignition electrode mounted on the front of the infrared burner just like the other Viking barbecue grill burners installed in these models.

viking trusear all infrared burner with ignitor electrode viking trusear infrared burner and igniter electrode

As shown in this image the double prong ignition electrode on the infrared Tru-Sear burner is mounted to the back of the burner in the Viking grill models that are All Infrared. This TruSear burner is only installed in all infrared models.

Viking gas grills with only one Tru Sear infrared grilling burner have the ignition electrode mounted on the front of the infrared burner just like the other Viking barbecue grill burners installed in these models.

Seen on the far right, the original electrode for the rotisserie had two ceramic housings linked with wire so the electrode was attached through the back wall and was attached again from inside the cover plate bracket.

When we replace the electrode ignition this is an annoying installation so instead we use the same electrode designed for the Viking burners and we mount the bracket under the cover plate above the thermocouple. The wire to the ignition module pulls through and attaches to the spade on the electrode.

Item Description Price Illustration

4488090

Viking gas barbeque grill Heavy Gauge electrode replacement used to repair Viking BBQ model igniters. In the ignition assembly, the electrode is like the spark plug. This electrode Sparks to ignite the U burner mounting next to the burner to light the gas as it leaves the barbecue grill burner.

$36.


Free Shipping Cont'l USA!!
gas bbq grill replacement electrode starter for viking gas bbq grills

4488091

Longer replacement electrode for Viking gas barbecue grill models ignite straight pipe burner, which Viking calls the smoker burner.

Image shows Original Electrode From Viking is designed with very long back side porcelain extension to protect round and electrode wiring passing through the control panel firewall for long term use with protection.

Yes, aftermarket generics are available ... but why risk a cheaper product when the Viking original is the same cost?

$37.


Free Shipping Cont'l USA!!
gas bbq grill replacement electrode starter for viking gas bbq grills
Viking BBQ Grill Parts Viking Control Valves Viking Ignition Flash Tubes
inside viking control panel igniter

These Original Viking electrodes are long enough in front of the mounting bracket to reach the ignition port holes on the burner BUT are Also long enough behind the mounting bracket to keep the wires away from any possibility of heat by passing through the second interior Viking fire wall.

small old viking electrode and collector box

The older Viking VGBQ models that used the smaller electrode and collector box has a Much Smaller Hole in the firewall so the double prong electrode would be too large to slide through the wall without making the holes larger.

viking rotisserie infrared burner